Type of Waste - What type of waste are you disposing of? You will need the right product of compaction equipment to accommodate your waste type. Size of Waste - How large are the items you will be disposing of? You will need a Feed Opening large enough to handle certain waste material. % of Recycling Material - Does your waste stream produce an efficient amount of recyclables to implement a compactor program? Energy Source - Does your building have adequate power available at the designated compactor location? Single or three phase? Safety - Are you following the recommended ANSI standards to make sure your installation complies? A 42" high barrier is required between the equipment user and the charge box. Does your equipment have an access interlock switch on chute or hopper doors and gates? Does your equipment have a "momentary contact" control need? Equipment Location - Does your designated compactor location have adequate height to support easy use? Is additional add-on equipment needed to accommodate your unit's location or handling needs (i.e., ozone odor control system, cart dumping system, etc.)?

Reduces hauling costs by compressing waste for fewer haul trips Requires less space for holding solid waste on site Controls odor and pest issues Reduces labor cost & increases operational efficiency Reduces fire hazards by containing waste in a confined container versus in the open air Positive environmental impact by reducing gas emissions

Recommendations: Union: Unax 46, Unax AW46 Gulf: Harmony 47, Harmony 48-AW Exxon: Teresstic 46, Nuto 46 Texaco: AW46 Shell: Turbo 46, Tellus 46 Quaker State: Dextron IIA Citgo: Pacemaker 46, Tellus AW46 Amoco: Rycon Please Note: You must check with a USA Environmental Services representative or the vendor installing the compaction equipment on the specific oil recommendations. There are a variety of compaction units that have different oil requirements.

Common Concrete Pad Requirements: The preferred dimensions of a concrete pad are 10'0" wide with a length of 5'0" greater than the length of the selected compactor & container. The pad should be a minimum of 3,000 PSI concrete steel reinforcement (6" thick). The concrete pad should be flush with the ground level. Containers that have four ground rollers must be installed on a level pad. For convenient access, the concrete pad needs to be positioned to allow 2'0" between the equipment and building wall if the unit is installed parallel with the building. A minimum of 45'0" of clearance is needed at the end of the pad for the hauling vehicle. Stationary compactors require a minimum of 28'0" of clear space on each side. Please Note: Our recommended clearances are minimums. Your site location and choice of equipment may require additional clearance space. Please Note: You must check with a USA Environmental Services representative or the vendor installing the compaction equipment on the specific concrete pad requirements. There are a variety of compaction units and location placement variables that play a role in the recommended concrete pad specification requirements.

Common Anchoring Requirements For Concrete Pads: The compactor should be anchored to a concrete pad using a minimum of four (4) 3/4" x 6" long anchor bolts. These bolts can be secured using a "Porok" or specialized concrete anchors. It is best if these holes are drilled into the concrete after pre-placing the compactor in the desired location. Holes in the leg plates are 1-5/16" Dia. to permit the use of 1-1/8" Dia. concrete bit. The 1-1/8" Dia. holes in the concrete should be about 5" deep. When the compactor unit has been permanently located, adjusted to compensate for unevenness, and anchor bolts set, tighten all nuts securely. Optional container guides should be anchored in an identical manner. Spacing between guides is determined by rail spacing of the container. Please Note: You must check with a USA Environmental Services representative or the vendor installing the compaction equipment on the specific anchoring requirements for your concrete pad. There are a variety of compaction units and location placement variables that play a role in the anchoring requirements for a concrete pad.

Common Troubleshoot Recommendations: Check the connection of the hydraulic hoses to the power pack of the compactor body. Check the disconnect. Is the disconnect on? Then press the reset button on the motor starter. If the unit has a jog control switch, confirm that the key switch is in the Remote position. If the Emergency Stop switch is a maintained push/pull switch, press and pull to the out position. Check the fuses. Do you have voltage flowing? Please Note: You must check with a USA Environmental Services representative or the vendor installing the compaction equipment on the specific Troubleshoot Recommendations. There are a variety of compaction units that have different instructions for Troubleshoot Recommendations.